www.BoundAnna.com

So I have been working in the shop for a few days and visiting the hardware store. Glad it is only 3 minutes from my house. And in my thread on Breast Clamps, I showed the prototype of a new device. This device does 3 functions, breast clamp, breast nipple suction and breast nipple pulling, all at the same time, if you want all three, or separately.

The frame is made of soldered copper pipe with the bottom and top hinging around a common pipe located about 9 inches away from the body. The top and bottom pipes are connected together with a single threaded rod with a tightening knob, located in the middle. From this common pipe, two vacuum operated two inch nipple cups are connected by threaded rods. Each cup rod has a tightening knob. The knobs were found to be easier to operate than wing nuts. Vacuum is supplied by a small hand operated vacuum pump.

Here is the completed device.
If anyone is interested I can provide a parts list.

And here it is in use... you can think of it as a breast extender or a breast straightener! Pull everything back into alignment. Lol.
It really pulls your breasts out and into the clamping pipes. If you have sufficient vacuum on the cups, it feels like you could pull your nipples hard enough to do some damage.

Here are more photos - https://ibb.co/album/JWHN43

Lumberjack, plumber, etc. Your talents are many!

Such a deceptively simple piece of hardware. Such potential fun!

Karren wrote:Pull everything back into alignment.

That reminds me... I have an appointment for a wheel alignment Friday.

I'll be sitting in the waiting area with a conspiratorial smile the whole time...

Great work, Karren!

Jenny.

Karren wrote:Here are more photos - https://ibb.co/album/JWHN43

It gets better and better. Well done, Karren.

bound_jenny wrote:Lumberjack, plumber, etc. Your talents are many!

Such a deceptively simple piece of hardware. Such potential fun!

Karren wrote:Pull everything back into alignment.

That reminds me... I have an appointment for a wheel alignment Friday.

I'll be sitting in the waiting area with a conspiratorial smile the whole time...

Great work, Karren!

Jenny.

Thanks Jenny! You know us Engineers! Jill of all trades, mistress of none! Think I should patent it? Sell it to chiropractors. Pretty sure that it could be used to center nipples or correct lopsidedness!

kinbaku wrote:

Karren wrote:Here are more photos - https://ibb.co/album/JWHN43

It gets better and better. Well done, Karren.

Thanks! Working on additional options and upgrades!

More options! Created a set of 3inch cups and a set of one inch cups. The larger cups had spikes glued inside which were removed after I tried it out this evening. I enjoy some discomfort but this hurt!

With the larger cups, which I am wearing as I type....
More Photos - https://ibb.co/album/RYBPRz

Karren wrote:With the larger cups, which I am wearing as I type....

larger cups.jpg

More Photos - https://ibb.co/album/RYBPRz

It's nice to make things for yourself and then test them. And at the same time you are aware of how you can improve it.

Created 4", 3", 2" and 1" tools.... Here's what they look like in order largest to smallest - https://ibb.co/M7kk3SW My breasts looks like a topographic map! lol.

bound_jenny wrote:
Such a deceptively simple piece of hardware. Such potential fun!

.

I think this thing is working, Jenny! My measurements normally are 37" under bust and 43" bust but after a couple sessions with this thing and my bust measurement has risen to 45"! And look a little more aligned! lol

Karren wrote:

bound_jenny wrote:
Such a deceptively simple piece of hardware. Such potential fun!

.

I think this thing is working, Jenny! My measurements normally are 37" under bust and 43" bust but after a couple sessions with this thing and my bust measurement has risen to 45"! And look a little more aligned! lol

Yup! Now you can open a kinky shop and advertise "Boob Alignments" among your services.

Put a couple of laser pointers on it and call it a "Laser Boob Alignment"...

(this is way too early... haven't finished my coffee yet... )

Jenny.

kinbaku wrote:It's nice to make things for yourself and then test them. And at the same time you are aware of how you can improve it.

I had to create a "bra" band using a bungee cord to hold it on during tool change or if I loose pressure.

Here's what they look like in order largest to smallest - https://ibb.co/M7kk3SW

Karren wrote:Here's what they look like in order largest to smallest - https://ibb.co/M7kk3SW

Very well made. And you yourself are the proof that it has an effect if you want to sell it on the market.

bound_jenny wrote:

Karren wrote:

bound_jenny wrote:
Such a deceptively simple piece of hardware. Such potential fun!

.

I think this thing is working, Jenny! My measurements normally are 37" under bust and 43" bust but after a couple sessions with this thing and my bust measurement has risen to 45"! And look a little more aligned! lol

Yup! Now you can open a kinky shop and advertise "Boob Alignments" among your services.

Put a couple of laser pointers on it and call it a "Laser Boob Alignment"...

(this is way too early... haven't finished my coffee yet... )

Jenny.

Everything is now perfectly laser aligned, Jenny! lol Thinking of adding WiFi, Bluetooth and maybe a USB port!

Karren wrote:Everything is now perfectly laser aligned, Jenny! lol Thinking of adding WiFi, Bluetooth and maybe a USB port!

You made me spit my coffee... And made my day.

Jenny.