Page 1 of 1

lock on a bra, how to do it

Posted: 23 Oct 2020, 04:15
by gwrolla
hey, its me again.

i love the way a bra feels, even better, when i have water balloons filled in it.

but, how can i trap myself in the bra, without ruining my bra?

Re: lock on a bra, how to do it

Posted: 23 Oct 2020, 04:26
by Shannon SteelSlave

Re: lock on a bra, how to do it

Posted: 23 Oct 2020, 04:38
by gwrolla
thanks, that enlighted me.

but now, my next question is this:

how can i make sure, that i dont cheat, and take out my water balloons?

Re: lock on a bra, how to do it

Posted: 23 Oct 2020, 04:47
by Shannon SteelSlave
Make a leather belt with 2 holes punched into it where the breasts go when wrapped around your chest. Fill the water balloons with water or something :twisted: Run the ends of the balloons through the holes in the belt and tie off the end with enough knots that it can not slip though.
If you try to pull them out, or try anything funny, they pop and you get soaked as a penalty. :twisted: You'll be the product of
8 X 6922251 = (Turn the number upside down)
And of course, you ruin your bra :rofl:

Re: lock on a bra, how to do it

Posted: 23 Oct 2020, 12:42
by Sergio
What will you be wearing over the bra because that's another way to stop cheating. The first method I used was a turtleneck body that I could padlock at the crotch (rather than using the hooks and eyes or poppers as intended, overlap the front and back flaps and put a padlock round so the fastenings can't pull through). But I've also used a turtle or tight round necked dress locked in place by a chain around the waist either through belt loops, or using the coin in pocket method. (If the dress has pockets, or if not, gather the fabric at a strategic point, in each side put a coin that's slightly larger than the hasp of a small padlock, then inside the dress loop the padlock around the fabric so the coin is trapped, hook onto the waist chain and snap shut.) With dress and heels locked on the only garment I can remove is the French knicker and that's assuming there isn't a chain between my heels.

Re: lock on a bra, how to do it

Posted: 24 Oct 2020, 14:21
by BoundInKasugai
Shannon SteelSlave wrote:You'll be the product of 8 X 6922251
:rofl:

Re: lock on a bra, how to do it

Posted: 25 Oct 2020, 02:43
by Blacky
Sergio wrote:What will you be wearing over the bra because that's another way to stop cheating. The first method I used was a turtleneck body that I could padlock at the crotch (rather than using the hooks and eyes or poppers as intended, overlap the front and back flaps and put a padlock round so the fastenings can't pull through). But I've also used a turtle or tight round necked dress locked in place by a chain around the waist either through belt loops, or using the coin in pocket method. (If the dress has pockets, or if not, gather the fabric at a strategic point, in each side put a coin that's slightly larger than the hasp of a small padlock, then inside the dress loop the padlock around the fabric so the coin is trapped, hook onto the waist chain and snap shut.) With dress and heels locked on the only garment I can remove is the French knicker and that's assuming there isn't a chain between my heels.

The turtleneck can be locked in the same fashion as described for the bra on brassiered.

@ Shannon:
That's mathematics put to strange use... :facepalm: :mrgreen:

Re: lock on a bra, how to do it

Posted: 25 Oct 2020, 10:23
by kinbaku
Blacky wrote: @ Shannon:
That's mathematics put to strange use... :facepalm: :mrgreen:
But as a mathematician I love it. :D :rofl:

Re: lock on a bra, how to do it

Posted: 12 Jan 2021, 09:23
by gwrolla
thank you.

i know, i havent posted, for a short time, but my water balloons, in my sports bra, are still there.

anyway, thanks, for the tips.

Re: lock on a bra, how to do it

Posted: 08 Jun 2021, 21:16
by leylaonedge
Hey All,

This might be another solution, if you have access to a 3D Printer

https://www.thingiverse.com/thing:4700208

I'm planning on using this through a bra, with limited modifications to the bra. I think I may just print some spacers/rivets for the towers you can see, so they can easily clear, and will glue them in, so the fabric doesn't rip outside the puncture.

Just Food for thought

L