DIY Copper Breast Clamp
DIY Copper Breast Clamp
I have made many different types of breast clamps out of different materials but this one is my favorite. It's made of two 15 inch long 1/2 inch copper pipes, two 6 inch long number 10 bolts, two number 10 washers and two number 10 wing nuts. My original design was straight but I curved this one to better conform to my body and capture more breast. Drill holes in each end and insert the bolts as shown in the photo below. Until today all mine have just used plain copper pipe but I have added teeth using 12 gage copper wire, bent and soldered to the top of one of the pipes. Plan to do the bottom one when I get some free time. Nice thing about this design is if you don't want to use the teeth just take it apart and move it to the bottom with the teeth away from the breast.
Don't mind my sloppy soldering, was in a hurry the complete it.
Going to try it out tonight and may add as "as-worn" photo later on.
Don't mind my sloppy soldering, was in a hurry the complete it.
Going to try it out tonight and may add as "as-worn" photo later on.
Re: DIY Copper Breast Clamp
The teeth are not as comfortable but really not as painful as I had thought. Depends on how tight... They do hold my breasts in place better than without teeth.
Here's a photo being worn. https://ibb.co/cw9x2Br
Also here's an older version using steel piping... Since it is straight it is much harder to grab the total breasts in it.
Here's a photo being worn. https://ibb.co/cw9x2Br
Also here's an older version using steel piping... Since it is straight it is much harder to grab the total breasts in it.
Last edited by Karren on 03 May 2022, 05:26, edited 1 time in total.
Re: DIY Copper Breast Clamp
Completed! Did a better job of soldering.
Re: DIY Copper Breast Clamp
Being worn. Not real comfortable and woke up with some welts on my breasts that did not go away for over a day. Do not mind the marks on my breasts.... had an intense session with the punishment bra a few days ago.
Tried it reversed with teeth up and they make great tie locations.... More photos here....
https://ibb.co/album/JWHN43
Tried it reversed with teeth up and they make great tie locations.... More photos here....
https://ibb.co/album/JWHN43
Re: DIY Copper Breast Clamp
Nice idea with those washers on your nipples. I was already on hot thinking with my dg lab hooked up to the copper tubing, copper wires and copper washers.
Re: DIY Copper Breast Clamp
If you could find a non conductive bolt then you could electrify the top rod against the bottom.kinbaku wrote:Nice idea with those washers on your nipples. I was already on hot thinking with my dg lab hooked up to the copper tubing, copper wires and copper washers.
Re: DIY Copper Breast Clamp
You have those plastic threaded rods that can serve. After all, there are not very great forces on the threaded rod. Only enough to push the soldered wires into your skin.Karren wrote:If you could find a non conductive bolt then you could electrify the top rod against the bottom.
- Shannon SteelSlave
- Moderator
- Posts: 6532
- Joined: 03 Feb 2019, 19:49
- Location: New England, USA
Re: DIY Copper Breast Clamp
You could use zip ties
Bondage is like a foreign film without subtitles. Only through sharing and practice can we hope to understand.
A Jedi uses bondage for knowledge and defense, never for attack.
I am so smart! I am so smart! S-M-R-T!....I, I mean S-M-A-R-T!
A Jedi uses bondage for knowledge and defense, never for attack.
I am so smart! I am so smart! S-M-R-T!....I, I mean S-M-A-R-T!
Re: DIY Copper Breast Clamp
Because this is curved, zip ties wouldn’t work well. Tried them early on. Needs some lateral support to keep it from rotating. A nylon threaded rod would.Shannon SteelSlave wrote:You could use zip ties
- Shannon SteelSlave
- Moderator
- Posts: 6532
- Joined: 03 Feb 2019, 19:49
- Location: New England, USA
Re: DIY Copper Breast Clamp
I suppose suggesting a radiator hose clamp would get me kicked out of here.........
You might also use a wooden rod and thread metal nuts. Make sure the diameter is large enough that the plastic or wood rod won't bend or snap. That would be bad. No more
You might also use a wooden rod and thread metal nuts. Make sure the diameter is large enough that the plastic or wood rod won't bend or snap. That would be bad. No more
Bondage is like a foreign film without subtitles. Only through sharing and practice can we hope to understand.
A Jedi uses bondage for knowledge and defense, never for attack.
I am so smart! I am so smart! S-M-R-T!....I, I mean S-M-A-R-T!
A Jedi uses bondage for knowledge and defense, never for attack.
I am so smart! I am so smart! S-M-R-T!....I, I mean S-M-A-R-T!
Re: DIY Copper Breast Clamp
They actually make radiator hose clamp type breast clamps! https://www.etsy.com/uk/listing/1000318 ... ather-bdsm
- Shannon SteelSlave
- Moderator
- Posts: 6532
- Joined: 03 Feb 2019, 19:49
- Location: New England, USA
Re: DIY Copper Breast Clamp
You could also try my idea, using the leather sleeving. viewtopic.php?f=12&t=12023 Those are better for cuffs and belts, as the upholstery does limit the sizing possibility.
Bondage is like a foreign film without subtitles. Only through sharing and practice can we hope to understand.
A Jedi uses bondage for knowledge and defense, never for attack.
I am so smart! I am so smart! S-M-R-T!....I, I mean S-M-A-R-T!
A Jedi uses bondage for knowledge and defense, never for attack.
I am so smart! I am so smart! S-M-R-T!....I, I mean S-M-A-R-T!
Re: DIY Copper Breast Clamp
Very interesting idea! I had read your thread on leather sleeving. Nice.Shannon SteelSlave wrote:You could also try my idea, using the leather sleeving. viewtopic.php?f=12&t=12023 Those are better for cuffs and belts, as the upholstery does limit the sizing possibility.
Re: DIY Copper Breast Clamp
Took me all of 10 minutes at the hardware store to come up with a Solution. Rubber Expansion Nuts and nylon washers isolates the top rail from the bolts.
Last edited by Karren on 06 May 2022, 04:37, edited 1 time in total.
Re: DIY Copper Breast Clamp
Then soldered on small terminals so I could attach my Tens unit (probably not powerful enough). Going to try it tonight.