Finished work on 3d printed chastity belt

Ideas and instructions how you can make your own bondage toys.
Post Reply
Tracker
*
Posts: 9
Joined: 27 Feb 2015, 01:02

Finished work on 3d printed chastity belt

Post by Tracker »

A while ago I started this thread:
viewtopic.php?f=12&t=9116

It has been several years since then, and I have been working on this project on and off. As you may appreciate, doing this takes a bit of effort and I often get bogged down in my day job. So, progress has been slow. But the good news is that I think I am finally happy with the design and have a finished result:

Image

Image

Rather than re post the same story on multiple forums, I decided to put everything together in 1 spot with better organization. As such, you can read all about it here:
https://www.deviantart.com/taridyn/art/ ... -930408621

and you can see all the pictures here:
https://www.deviantart.com/taridyn/gallery
User avatar
Shannon SteelSlave
Moderator
Posts: 6531
Joined: 03 Feb 2019, 19:49
Location: New England, USA

Re: Finished work on 3d printed chastity belt

Post by Shannon SteelSlave »

Can you tell us what the tab on the roll pin is for?
Bondage is like a foreign film without subtitles. Only through sharing and practice can we hope to understand.
A Jedi uses bondage for knowledge and defense, never for attack.
I am so smart! I am so smart! S-M-R-T!....I, I mean S-M-A-R-T!
👠👠
User avatar
Gregovic
****
Posts: 1119
Joined: 26 Mar 2016, 21:31
Location: Netherlands

Re: Finished work on 3d printed chastity belt

Post by Gregovic »

Tracker wrote:A while ago I started this thread:
viewtopic.php?f=12&t=9116

It has been several years since then, and I have been working on this project on and off. As you may appreciate, doing this takes a bit of effort and I often get bogged down in my day job. So, progress has been slow. But the good news is that I think I am finally happy with the design and have a finished result:

Image

Image

Rather than re post the same story on multiple forums, I decided to put everything together in 1 spot with better organization. As such, you can read all about it here:
https://www.deviantart.com/taridyn/art/ ... -930408621

and you can see all the pictures here:
https://www.deviantart.com/taridyn/gallery
That's certainly some very nice design work you've done there. I didn't have time to post a reply when you posted it and then completely forgot about the post :oops:
How did you come up with that rather extreme looking plug design? I would never really have occurred to me to "go around the bend" like that. I'm not very experienced with "back door" play but it somehow just doesn't look like it should fit.

How is the 3d printed material in terms of porosity and taking up smells or harbouring bacteria?
How may I serve you? *Curtsey*
User avatar
Shannon SteelSlave
Moderator
Posts: 6531
Joined: 03 Feb 2019, 19:49
Location: New England, USA

Re: Finished work on 3d printed chastity belt

Post by Shannon SteelSlave »

Gregovic wrote: I didn't have time to post a reply when you posted it and then completely forgot about the post :oops:
That's one reason I do these "Orphan post runs".
Bondage is like a foreign film without subtitles. Only through sharing and practice can we hope to understand.
A Jedi uses bondage for knowledge and defense, never for attack.
I am so smart! I am so smart! S-M-R-T!....I, I mean S-M-A-R-T!
👠👠
Tracker
*
Posts: 9
Joined: 27 Feb 2015, 01:02

Re: Finished work on 3d printed chastity belt

Post by Tracker »

To answer some questions:

Can you tell us what the tab on the roll pin is for?

I am not sure exactly what you are asking about, but I think you mean the cylinder on the end of the locking shaft. The lock I use is a ratchet type. You can push the shaft in without the key, but need the key to release the lug and pull it back out. That cylinder prevents the shaft from being pulled through. It also allows you to grab and pull the shaft out to unlock the belt.

As for the shape of the plug and why it points backwards, that's what humans look like inside. Just google 'pelvis cross section' and see for yourself. Human anatomy and porn don't line up.

You can put almost any shape back there for a short period of time, as the intestines are flexible. But, if you want to wear it for a longer period of time (overnight), then you need to follow human anatomy better, especially if it is attached firmly in place to the belt and unable to move/rotate like a normal plug can.

As for the material, I used this:
https://www.sculpteo.com/en/materials/j ... k-plastic/

It is a bit more expensive than the material you find used on cheap 3d printed cages. But it is watertight and chemical resistant. I.E. it doesn't have problems with porosity.

As for the smell, I take it off for a good cleaning once a week. That seems to be good enough to prevent any odor problems.
Post Reply