3D print: prevent removeal of clover-clamps

Ideas and instructions how you can make your own bondage toys.

3D print: prevent removeal of clover-clamps

Postby occorics » 21 Jun 2021, 15:05

this is a 3D printed prototype to prevent clover-clamps from being removed...
With one lock, it might still be possible using tools, but with a 2nd lock on the other side, the handle is held open and tools won't help... :twisted:

the weight of the locks is another evil side-effect...

20210621_165150.jpg
20210621_165220.jpg
maid marta, Collared property of Domina Shelle Rivers and Lady Helena

https://twitter.com/ShellesPuppy
my blog: https://owned-by-princess-shelle.blogspot.com
my art: https://maid-marta.bdsmlr.com
User avatar
occorics
***
 
Posts: 368
Joined: 31 May 2016, 10:46
Location: Germany

Re: 3D print: prevent removeal of clover-clamps

Postby kinbaku » 21 Jun 2021, 15:53

occorics wrote:this is a 3D printed prototype to prevent clover-clamps from being removed...
With one lock, it might still be possible using tools, but with a 2nd lock on the other side, the handle is held open and tools won't help... :twisted:

the weight of the locks is another evil side-effect...

20210621_165150.jpg
20210621_165220.jpg

I already used a lock to prevent the clamps from being opened again. However, this is version 2.0.
With 2 locks you are assured of the necessary experience. :twisted: :mrgreen:
User avatar
kinbaku
*****
 
Posts: 3059
Joined: 10 Jan 2020, 19:26
Location: Belgium

Re: 3D print: prevent removeal of clover-clamps

Postby bounddosster » 23 Jun 2021, 08:25

kinbaku wrote:
occorics wrote:this is a 3D printed prototype to prevent clover-clamps from being removed...
With one lock, it might still be possible using tools, but with a 2nd lock on the other side, the handle is held open and tools won't help... :twisted:

the weight of the locks is another evil side-effect...

20210621_165150.jpg
20210621_165220.jpg

I already used a lock to prevent the clamps from being opened again. However, this is version 2.0.
With 2 locks you are assured of the necessary experience. :twisted: :mrgreen:


I also use a padlock to stop them from being removed by fitting it around the main pivoting piece under the finger grips where you squeeze to open them.

I don't want to put a downer on it, great work and effort but if your going to use tools you could just cut the plastic away and squeeze it to release but the pulling and tugging by doing such an operation would result in some interesting sensations on the nipple.
Doing my bit for the environment by going naked to save the planet.
User avatar
bounddosster
****
 
Posts: 1152
Joined: 30 Jan 2014, 22:23
Location: England.

Re: 3D print: prevent removeal of clover-clamps

Postby occorics » 24 Jun 2021, 07:46

bounddosster wrote:
kinbaku wrote:
occorics wrote:this is a 3D printed prototype to prevent clover-clamps from being removed...
With one lock, it might still be possible using tools, but with a 2nd lock on the other side, the handle is held open and tools won't help... :twisted:

the weight of the locks is another evil side-effect...

20210621_165150.jpg
20210621_165220.jpg

I already used a lock to prevent the clamps from being opened again. However, this is version 2.0.
With 2 locks you are assured of the necessary experience. :twisted: :mrgreen:


I also use a padlock to stop them from being removed by fitting it around the main pivoting piece under the finger grips where you squeeze to open them.

I don't want to put a downer on it, great work and effort but if your going to use tools you could just cut the plastic away and squeeze it to release but the pulling and tugging by doing such an operation would result in some interesting sensations on the nipple.


Yes, of course you can cut the plastic, although PLA is quite strong.
I also found that it's possible to tilt the covers to the sides enough to reach the lower part of the clamp. It might be possible to use a lever there to open them enough to remove.
I'm now thinking about something like those metal chastity bras, but with a lockable hatch to be able to secure the clamps inside...
maid marta, Collared property of Domina Shelle Rivers and Lady Helena

https://twitter.com/ShellesPuppy
my blog: https://owned-by-princess-shelle.blogspot.com
my art: https://maid-marta.bdsmlr.com
User avatar
occorics
***
 
Posts: 368
Joined: 31 May 2016, 10:46
Location: Germany

Re: 3D print: prevent removeal of clover-clamps

Postby VooKink » 19 Jan 2022, 22:10

Haha That is evil! can you link the .stl?
VooKink
*
 
Posts: 2
Joined: 19 Jan 2022, 22:04

Re: 3D print: prevent removeal of clover-clamps

Postby Shannon SteelSlave » 20 Jan 2022, 01:16

Welcome to Bound Anna, VooKink
Bondage is like a foreign film without subtitles. Only through sharing and practice can we hope to understand.
A Jedi uses bondage for knowledge and defense, never for attack.
I am so smart! I am so smart! S-M-R-T!....I, I mean S-M-A-R-T!
User avatar
Shannon SteelSlave
*****
 
Posts: 4465
Joined: 03 Feb 2019, 18:49
Location: New England, USA

Re: 3D print: prevent removeal of clover-clamps

Postby VooKink » 20 Jan 2022, 02:53

Thankyou :)
VooKink
*
 
Posts: 2
Joined: 19 Jan 2022, 22:04

Re: 3D print: prevent removeal of clover-clamps

Postby kinbaku » 20 Jan 2022, 09:05

Welcome to BoundAnna VooKink and enjoy the print when you get the .sti.
User avatar
kinbaku
*****
 
Posts: 3059
Joined: 10 Jan 2020, 19:26
Location: Belgium

Re: 3D print: prevent removeal of clover-clamps

Postby lj » 20 Jan 2022, 11:04

Here's an alternative I came up with ages ago.

I'd been making some spreader bars out of broom-handles, just cut to length then some heavy gauge screw eyelets, one in each end, perhaps one in the middle. A couple were cut about 15" (40cm approx). Have a loose lockable collar and cuffs, padlock one end of each bar to the collar, at the front, padlock the cuffs to the other ends, one on each. Now you can freely use your hands, but you can't get them anywhere near your face or chest (or genitals if you get the length right)

So just put the clamps on and any other tortures to other parts before you lock the cuffs to the bar ends.

You could also use chains and a couple of metal or rigid plastic tubes to replace the wooden bars.
be a switch, double the fun :-)
lj
Moderator
 
Posts: 2205
Joined: 14 Oct 2008, 16:22
Location: East Anglia, UK

Re: 3D print: prevent removeal of clover-clamps

Postby occorics » 26 Jan 2022, 09:01

VooKink wrote:Haha That is evil! can you link the .stl?


i need to see if i still have it somewhere...
In the end, it didn't work as intended, i found an easy way out after a while and haven't found a way to improve the design yet...
maid marta, Collared property of Domina Shelle Rivers and Lady Helena

https://twitter.com/ShellesPuppy
my blog: https://owned-by-princess-shelle.blogspot.com
my art: https://maid-marta.bdsmlr.com
User avatar
occorics
***
 
Posts: 368
Joined: 31 May 2016, 10:46
Location: Germany


Return to DIY

Who is online

Users browsing this forum: Ahrefs [Bot], Google [Bot] and 3 guests