Need Help with a Fuck Machine

Ideas and instructions how you can make your own bondage toys.
Post Reply
sunset_burst
*
Posts: 1
Joined: 09 May 2014, 05:55

Need Help with a Fuck Machine

Post by sunset_burst »

Ok this is going to be a long shot. I know nothing about building stuff. I mean I'm pretty smart and crafty but if you gave me a motor I wouldn't know what to do with it. I really can find a GOOD diy step by step guide on the web.
I wanna make a fuck machine that can fit inside of a tool box (for privacy purposes).
Something relatively easy to make. Stroke length of several inches 4-6 would be nice.
I see all this stuff about dc motors and shit and I'm lost. As far as converting the rotating motor to linear movement I get that and I am sure I can figure it out.
The confusing part is the wiring and getting power source as well as varying speeds.
The fukbox sounds like something I want....however I don't want to pay the 20$ for the schematics. Especially if I don't know how helpful they will be or not. If anyone has ever made a fuck machine let me know. I would like some ideas, insight, and guidance.
I'm trying to shoot for a budget of 200$.
User avatar
Sir Cumference
Moderator
Posts: 1606
Joined: 29 Jan 2012, 22:00
Location: Scandinavia

Re: Need Help with a Fuck Machine

Post by Sir Cumference »

There is a reason why you see rubber/plastic models all over the place at a low cost: They are really easy to make. You just make a mold and cast them.

You also see lots of vibrators at reasonably low cost, because it is pretty easy to make something vibrate (you have to be careful to avoid vibration). And putting a vibrator into a casting, is not much of a problem either.

You do not see fucking machines a lot, because they are mechanically complicated. If you want them to work and last, you must use quality parts, and that adds to the cost.

The Luvbights have some pretty nice photos http://luvbight.com/mesh/galleries/p0402fm/photo24.html (And they have named their machines! Arnold, Jack and Franz I-III)


You are honest, and that is great, but
I know nothing about building stuff.
is not really a good starting point when you are going to do something that requires combining mechanics, electronics, woodworking and metalworking.... and is supposed to act on someones tender parts!
~ Leatherworking, blacksmithing , woodworking and programming are the most pervertable skills you can learn! ~
User avatar
Sir Cumference
Moderator
Posts: 1606
Joined: 29 Jan 2012, 22:00
Location: Scandinavia

Re: Need Help with a Fuck Machine

Post by Sir Cumference »

Here is a couple of links to other "builders":
http://www.orgasmatronics.com/pages/abo ... n#building (about building heavy duty vibrators)
~ Leatherworking, blacksmithing , woodworking and programming are the most pervertable skills you can learn! ~
User avatar
boundsissy
**
Posts: 196
Joined: 07 Jul 2010, 01:51
Location: sub of Chicago

Re: Need Help with a Fuck Machine

Post by boundsissy »

It took me a while to find this article, I knew I read it at one time though, and just in case you are thinking of trying something stupid.
http://www.thebaynet.com/news/index.cfm ... y_ID/12368
LOVE TO ALL
Tenderfoot88
***
Posts: 458
Joined: 17 Sep 2013, 08:00
Location: British Columbia, Canada

Re: Need Help with a Fuck Machine

Post by Tenderfoot88 »

Oh, wow. I know exactly what the inspiration is, but....how did they think using a sharp blade was a viable alternative to the proper adapter? Obviously a case of enthusiasm running well ahead of sense....

As for a toolbox sized fucking machine, unless you're really comfortable working with electric motors, you're better off buying one. (Having taken a single course in the mechanics of electric motors, the only thing about them I'm comfortable with is the knowledge that mines also employ electrical engineers to look after such matters.) While places like http://www.kenstwistedmind.com and http://www.orgasmalley.com are probably among the best sources, neither have the toolbox design you're looking for. However, http://www.extremerestraints.com does. About 550 USD, less if it's on sale - expensive, yes, but getting a decent motor and all the other necessary components would probably run you at least half of that, and then you need the expertise to put it all together, calibrate it, etc.
User avatar
Sir Cumference
Moderator
Posts: 1606
Joined: 29 Jan 2012, 22:00
Location: Scandinavia

Re: Need Help with a Fuck Machine

Post by Sir Cumference »

And extreme restraints university even have a demo movie
http://www.xruniversity.com/xr-u-show-sex-machines/
~ Leatherworking, blacksmithing , woodworking and programming are the most pervertable skills you can learn! ~
machineyourself
*
Posts: 2
Joined: 29 Jul 2014, 01:25

Re: Need Help with a Fuck Machine

Post by machineyourself »

I have a site that tries to help the amateur builder like yourself... I don't offer any specific plans but I give suggestions and shopping lists to build reliable machines starting at around $175. You'll have to do the work and follow some of my tutorials, but I try to make it as simple as possible. I do sell parts for those who need them, but I keep all my content free.

The site is www.machineyourself.com.

You can also email me through the site if you have questions that aren't covered there...
Brand X mk2
**
Posts: 80
Joined: 07 Oct 2013, 12:40

Re: Need Help with a Fuck Machine

Post by Brand X mk2 »

I would suggest buying either a basic unit and build your own stand and add-ons, or buy a kit: http://www.orgasmalley.com/diyparts.htm
Incidentally, I've just discovered you can rent fucking-machines even in the UK.
uncannymoebius
**
Posts: 98
Joined: 23 Mar 2014, 08:39

Re: Need Help with a Fuck Machine

Post by uncannymoebius »

Uh why don't you just get a reciprocating saw and exchange the blade with something like this ?http://www.amazon.com/gp/aw/d/B00IPQNA6 ... ot_redir=1

Then you need a dildo and you could build a mount.
User avatar
boundsissy
**
Posts: 196
Joined: 07 Jul 2010, 01:51
Location: sub of Chicago

Re: Need Help with a Fuck Machine

Post by boundsissy »

uncannymoebius wrote: get a reciprocating saw and exchange the blade with something like this ?http://www.amazon.com/gp/aw/d/B00IPQNA62?pc

Then you need a dildo and you could build a mount.
This is the funniest thing I have seen (could anyone take 40 strokes a second with a dildo?) :rofl: Even better get a jack hammer and put a dildo on the end :rofl:
LOVE TO ALL
machineyourself
*
Posts: 2
Joined: 29 Jul 2014, 01:25

Re: Need Help with a Fuck Machine

Post by machineyourself »

boundsissy wrote:
uncannymoebius wrote: get a reciprocating saw and exchange the blade with something like this ?http://www.amazon.com/gp/aw/d/B00IPQNA62?pc

Then you need a dildo and you could build a mount.
This is the funniest thing I have seen (could anyone take 40 strokes a second with a dildo?) :rofl: Even better get a jack hammer and put a dildo on the end :rofl:

I have been making and selling these fucksaw adapters for about a year now... They are becoming more and more popular, and I can assure you that many people can take 40 strokes a second with a dildo. The reason you can go at such high speeds is the short stroke length (about 1.25 inches) of the sawzaw. As the stroke length goes up, you have to slow things down a bit though.

If you do a google search for fucksaw adapter or look on my website, you will see them in action.
Post Reply