Tuto DIY Bondage gear - Part 2 Ring gag & Blindfold

Ideas and instructions how you can make your own bondage toys.
Post Reply
Greenleaf
*
Posts: 32
Joined: 08 Jun 2016, 10:40

Tuto DIY Bondage gear - Part 2 Ring gag & Blindfold

Post by Greenleaf »

Hello everybody! :hi: I make this post to show you how i create my bondage gear.

In this second episode, I'll show you how I proceed to create a ring gag and a blindfold and what materials are needed for that.
If you don't know how to sew (because you'll have to sew) you can go to the first episode "Tuto DIY Bondage gear - Part 1 Intro & basics" --> http://forum.boundanna.net/board/viewto ... 12&t=11053
It's not a perfect technique but it's good enough.

The materials :
►100% cotton straps, width : 1.5 cm
►Pieces of black velvet : 6cm x 46cm (approximately, it depends of your head mesurement)
►Galvanized steel ring : Ø4.3cm (approximately, You must be able to keep it in the mouth without it causing you any cramps)
►Clip buckles : it should be the good size for the 1.5 cm cotton strap
►Black thread and needles

The Ring gag :
tutogag.png
(10.87 KiB) Downloaded 3184 times
For more visibility, I draw the cotton straps in red

I began by sewing two lengths of cotton strap on each side of the ring. The left part of the buckle is adjustable so I just let enough lenght for adjusting but the other side must be sewn so the right strap must be half your head mesurement plus 3 or 4 cm to sew.

There is an alternative more simple to do :
IMG_20170515_182411.jpg
(woohoo! my first own picture posted in this website!)
This one was made just with the steel ring and some black elastic ribbon; 2cm width (not mentioned in the materials section), the lengh of the ribbon is EXACTLY your head mesurement so when you sew it, it will be a little bit smaller than your head and the elastic will be stretched when you'll wear it.

The Blindfold :
tutoblindfold.png
(5.07 KiB) Downloaded 3184 times
To do this one, it's exactly the same process than for the ring gag but the ring is replaced by the vlevet piece.

I hope it was enough clear and understandable and that you had as much fun reading this tutorial as I had when i wrote it! :D
Do not hesitate to give me your opinions, they are always welcome.

Cya! :love:

G.
User avatar
ponylady
Moderator
Posts: 3822
Joined: 26 Dec 2007, 20:52
Location: germany
Contact:

Re: Tuto DIY Bondage gear - Part 2 Ring gag & Blindfold

Post by ponylady »

Thank you for the tutorial.

A bit of advice:

Covering the ring in 2 layers of liquid latex (or similiar)
Will make your dentist happy.

Human teeth aren't meant to grate on steel.
[
User avatar
Gregovic
****
Posts: 1118
Joined: 26 Mar 2016, 21:31
Location: Netherlands

Re: Tuto DIY Bondage gear - Part 2 Ring gag & Blindfold

Post by Gregovic »

ponylady wrote:Thank you for the tutorial.

A bit of advice:

Covering the ring in 2 layers of liquid latex (or similiar)
Will make your dentist happy.

Human teeth aren't meant to grate on steel.

Strictly speaking I think NOT doing so makes the dentist happy. Crowns and dentures are expensive :wink: Dipping in latex WILL make YOU happier though.
How may I serve you? *Curtsey*
Greenleaf
*
Posts: 32
Joined: 08 Jun 2016, 10:40

Re: Tuto DIY Bondage gear - Part 2 Ring gag & Blindfold

Post by Greenleaf »

Thank you Ponylady & Gregovic for the advice, it's a good idea!
I will buy some liquid latex to put it on the ring.
Post Reply